- #VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD GENERATOR#
- #VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD DRIVER#
- #VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD LICENSE#
- #VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD WINDOWS 7#
ġ5 F INAL SECTION IDLING CURRENT ALIGNMENT Connect the 50 Ohm Dummy Load to the ANT jack. Remove the shorting-plug from J2003 on the PA Unit, then connect the DC Ammeter to J2003 (pin 1: “–” lead, pin 2. Inject a 19.900 MHz signal from the RF Sig.ġ4 Alignment PA Unit Alignment PRE-DRIVER SECTION IDLING CURRENT ALIGNMENT Connect the 50 Ohm Dummy Load to the ANT jack.
#VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD GENERATOR#
Note: Signal levels in dB referred to in the align.ġ3 Alignment Receiver Alignment RX IF COILS ALIGNMENT Connect the RF Signal Generator to the ANT jack, and connect the AF millivoltmeter to the EXT SP jack. Also, the test equipment must be thorough- ly warmed up before beginning. All component replacem.ġ2 Alignment Whenever possible, alignments should be made with oscillator shields and circuit boards firmly affixed in place. Realignment should therefore not be necessary except in the event of a component failure.
#VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD DRIVER#
The RF signal is then applied to J1001 on the MAIN Unit, and passed through the limiter ci.Ĩ Circuit Description On the PA Unit, the low-level RF signal from the MAIN Unit is amplified by pre-driver Q2001 (RD06HHF1), push-pull driver Q2008/Q2009 (both RD16HHF1), and push-pull final amplifier Q2012/ Q2013 (both SD1405), which provides up to.ĩ Circuit Description Control Circuit Major frequency control functions such as channel selection, display, and PLL divider control are per- formed by main CPU Q1018 (HD64F2134) on the MAIN Unit, at the command of the user via the tun- ing knob and f.ġ0 Connector Pinout Diagrams +13.8 V OUT TX GND GND BAND DATA A TX-INH EXT ALC Input TX REQ BAND DATA B BAND DATA C BAND DATA D MIC Jack GPS Jack ACC Jack TUNE Jack DATA Jack ( As Viewed From Rear Panel )( As Viewed From Rear Panel ) ( As Viewed From.ġ1 Alignment The VX-1700 is carefully aligned at the factory for the specified performance across the entire operat- ing frequency range. Ģ Specifications General Receiver Frequency Range: 30 kHz ~ 30.0000 MHz Transmitter Frequency: 1.600 ~ 30.0000 MHz Emission Modes: A1A (CW), J3E (LSB/USB), A3E (AM), J2B (USB/LSB), Frequency Synthesizer Step: 10 Hz, 100 Hz, 1 kHz Frequency Stability.ģ Exploded View & Miscellaneous Parts RA0725400 FRONT PANEL ASSY RA0695500 PACKING PAD (CHASSIS) RA0694800 KNOB (L) RA0694900 KNOB (S) RA069430A RUBBER KNOB (4KEY) RA069420A RUBBER KNOB (12KEY) RA069440A RUBBER KNOB (UP/DOWN) RA069450A RUBBER KNO.Ĥ Exploded View & Miscellaneous Parts Noteħ Circuit Description Receive Signal Path Incoming RF signal from the ANT jack is delivered to the PA Unit, and passes through the TX/RX relay RL2009 to J2006.
#VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD LICENSE#
Warning Be advised, serious penalties and prosecution can result from unlicensed transmission on frequencies which require a license, and/or interference with public safety transmissions.Īll Land Mobile radios (LMR) require an FCC license to operate.1 Contents Specifications. Once your order has been processed you can download your software using your account login. Important: You must LOGIN to your account BEFORE you order this software. Note: Software downloads cannot be cancelled, exchanged, or returned for refund once the order has been processed.
For EVX-R70: CT-151 Cloning Cable (USB type).Vertex-Standard accessories ( Sold Separately):.
#VERTEX STANDARD PROGRAMMING SOFTWARE DOWNLOAD WINDOWS 7#
To use this software, the following hardware and software are required: This software is designed to set frequencies and functions for the Vertex-Standard VXD-720, VXD-7200 radios. Vertex Standard CE-VSCE v5.0 Programming Software for EVX-R70 - Download Only